dictionary = 
{
    ["DictKey_ActionText_29"] = "When the ground power is disconnected, close the canopy.\
\
Click on the canopy lever.",
    ["DictKey_ActionText_36"] = "",
    ["DictKey_ActionText_33"] = "Left-click to turn on all the light switches on the lights panel. As long as you are not on a combat mission or still over friendly territory, always use at least your position lights.",
    ["DictKey_ActionText_66"] = "",
    ["DictKey_ActionText_58"] = "Check that your flaps are between 1/2 and 1, your external lights are on and the plane does not show any warnings.\
\
Move the throttle to full power and release the brakes. Use the wheel brakes to keep the plane on the runway.",
    ["DictKey_ActionText_70"] = "Hit [ESC] to end the mission.",
    ["DictKey_ActionText_26"] = "With the radio turned on and the channel set, we can contact the ATC.\
\
Press the comm button and then F5 (ATC), F1 (Andersen AFB) and the F3 (ask for permission for engine start).\
\
[Hit the space bar to continue]",
    ["DictKey_ActionText_38"] = "Now it is time to put the flaps out.\
Watch the flap gauge on the left panel and push the flap lever down by left-click. When the flaps are at 1/2 position right-click on the flap lever to stop the flaps in the 1/2 position.  Left-click the spoilers swicth to arm the spoilers.",
    ["DictKey_ActionText_23"] = "",
    ["DictKey_ActionText_49"] = "Well done. That was the right direction.",
    ["DictKey_ActionText_44"] = "Turn left on the taxi way.\
Always try to taxi with your nose wheel on the centerline.",
    ["DictKey_ActionText_69"] = "",
    ["DictKey_ActionText_61"] = "Push the nose down to reduce nose wheel bouncing. Watch your IAS and pull the stick gently towards you when you exceed 150 knots.",
    ["DictKey_ActionText_15"] = "Now right click on the channel selector to choose channel 2.",
    ["DictKey_ActionText_6"] = "Welcome to the A4-E-C Skyhawk. In this mission we will learn how to do a cold start, taxi to the runway and finally takeoff.\
\
First of all, we will get familiar with the involved controls for this training.\
\
[Hit the space bar to continue]",
    ["DictKey_ActionText_47"] = "You turned right but you were told to turn left! Turn around and go the other direction!",
    ["DictKey_ActionText_54"] = "At this point it is a good idea to watch out for traffic.",
    ["DictKey_ActionText_63"] = "",
    ["DictKey_ActionText_37"] = "We are ready to taxi to the runway. Request permission to taxi to the runway.\
\
Press the Comm button and then F5 (ATC) F1 (Andersen AFB) and the F1 (ask for permission to taxi to the runway).\
\
[Hit the space bar to continue]",
    ["DictKey_ActionText_41"] = "When the ATC gave the permission to taxi to runway 6L, you can start to roll.  Make sure you have not applied the wheel brakes. \
Increase the power with the throttle gently until the plane starts to move. Reduce the power again to keep a safe speed, but keep rolling.\
\
The A-4E-C can easily flipped over if you are too fast while steering. Use the differential wheel brakes to steer.\
Either map the differential wheel brakes to your pedals or use [ALT + W] to brake the right wheel and [Ctrl + W] for the left wheel, which will turn you in the according direction. Use [W] to apply both brakes.",
    ["DictKey_ActionText_32"] = "Turn on your cockpit lights. \
Turn the instruments and panel light knobs to your desired brightness. \
Also turn the white floodlight to the desired value.\
\
Right-click to turn on the external lights master switch at the outer side of the throttle lever.",
    ["DictKey_ActionText_56"] = "Turn right onto the runway. Place the plane in the middle of the runway and align to the runway.\
\
Move throttle in idle position and apply the wheel brakes.",
    ["DictKey_descriptionBlueTask_3"] = "",
    ["DictKey_ActionText_51"] = "Fork to the right to get to the runway.",
    ["DictKey_ActionText_9"] = "The Skyhawk does not have battery power, so we need to ask for external power. Contact the ground crew and ask for external power supply.\
\
Press the comm button and then F8 (ground crew) F2 (external power supply) and the F1 (turn on).\
Make sure the canopy is open, so the ground crew can hear you.\
\
[Hit the space bar to continue]",
    ["DictKey_descriptionText_1"] = "",
    ["DictKey_ActionText_64"] = "When you are airborne click on the gear lever to take the gear up and climb to a safe altitude. At 170 knots put your flaps up and accelerate.",
    ["DictKey_ActionText_67"] = "Well done. This ends this training. \
\
Hit [ESC] to end this training.",
    ["DictKey_descriptionRedTask_2"] = "",
    ["DictKey_descriptionNeutralsTask_4"] = "",
    ["DictKey_ActionText_59"] = "",
    ["DictKey_ActionText_18"] = "Set the radio frequency by clicking the three frequency selecting knobs to 250.1 MHz",
    ["DictKey_sortie_5"] = "",
    ["DictKey_ActionText_8"] = "Once we have the permission to start the engine we can start the engine up.\
\
First of all, we need to get to know the RPM gauge on the right side of the front panel, the starter button on the left panel close to the throttle lever and the throttle itself.\
The throttle lever has three stages: OFF, IGNITION and IDLE. Do a right-click on the throttle lever to switch through the stages from OFF over IGN to IDLE and left-click to switch back to OFF.\
\
Make sure the throttle lever is in OFF position.\
Press the starter button and watch the RPM gauge.\
On 5% RPM move the throttle to IGN position.\
On 15% RPM move the throttle to IDLE position.\
Once the RPM exceeds 40% you can call the ground crew to disconnect the ground power.\
\
Press the Comm button and then F8 (Ground Crew) F2 (external power supply) and the F2 (turn off).\
\
[Hit the space bar to continue]",
    ["DictKey_ActionText_21"] = "",
    ["DictKey_ActionText_12"] = "Since we are not alone on this airfield we want to ask for permission from the tower before we perform any action.\
The A4-E-C is equipped with a UHF radio to talk to the ATC or other planes.\
\
We need to set the radio frequency to the frequency the ATC uses. In this case it is 250.1 MHz You can use the manual mode or use the right preset channel.\
Then turn the UHF mode knob to T/R with a  right click. Use the frequency mode switch to choose between preset channel and manual mode.",
} -- end of dictionary
